Sisteme de cofraje
 

LAB

 

Platforma uşoară de lucru

Domenii de utilizare Caracteristici / Avantaje Lista de produse
 

Durabilă, economică, fiabilă

La realizarea schelelor pentru construcţia zidăriei, siguranţa are prioritate maximă. Alte cerinţe sunt după cum urmează: 

- disponibilitate rapidă pentru utilizare
- transport eficient
- depozitare optimizată
- mai puţine platforme pentru toate formele de contur din plan

Platforma de lucru LAB 130 îndeplineşte toate aceste cerinţe. Ea se livrează gata asamblată pentru a putea fi utilizată imediat drept platformă de lucru sau de protecţie. Platforma de lucru LAB 130 este în conformitate cu norma DIN 4420, putând fi utilizată până la grupa de platforme 4 (300 kg/m²).

Execuţie

CARACTERISTICI

AVANTAJE

  • poate fi utilizată direct din stivă: se ridică parapetul, se agaţă în macara, se coboară consola, se ridică, se montează
  1. asamblare rapidă, în siguranţă de la început
  • suport pentru stivuire şi dispozitiv împotriva alunecării din stivă încorporate
  1. transport al stivei optim şi sigur
  • platforma de lucru LAB 130/240 şi platforma de compensare încap puse transversal în orice camion
  1. cheltuieli reduse de transport
  • înălţime de stivuire de cca. 30 cm
  1. sunt transportate cel puţin şapte platforme per stivă
  • lungimi ale platformelor de 340, 240 cm şi platformă de colţ variabilă
  1. platformele pot fi montate la construcţii cu unghiuri drepte sau variabile în plan
  • metode de montaj la alegere: dispozitiv de agăţare tip buclă, papuc ancoraj sau ţeavă de agăţare

  1. elementul potrivit de fixare pentru fiecare utilizare
  2. schela pentru montaj armătură – posibilă până la o înălţime de maxim 6,00 m
  3. montare cofraj – posibilă până la o înălţime de maxim 5,40 m



Construcţie

 CARACTERISTICI

AVANTAJE

  • platforma este din aluminiu cu suprafaţă antiderapantă, într-o construcţie din cadre de oţel zincate la cald 
  1. durată lungă de viaţă cu necesitate redusă de curăţare
  2. siguranţă mare la deplasarea pe platformă
  • parapetul şi supraînălţarea au integrate din fabricaţie grilaje de protecţie, putând fi folosite ca platforme de siguranţă pentru acoperiş
  1. nu este necesară nicio plasă suplimentară de protecţie
  • platformă de compensare 240 pentru completarea spaţiilor între platforme de până la 200 cm 

  1. compensarea sistematică şi rapidă în afara modulului de lungime a platformelor fără soluţii speciale
  • platformă de colţ pentru toate unghiurile drepte şi obtuze, ca platformă de compensare
  1. fără proiectare adiţională: adaptare la toate formele planurilor
Deschide detalii
Închide toate detaliile
 

Working platform LAB 130

Working platform LAB 130Zoom
galvanized, railings and brackets are made of tubes Ø 48,3 mm. The guard-railing is provided with a protective steel mesh (width 100x100 mm), the platform is covered with a non-slipping aluminium on a hot-dip galvanized steel frame construction. Stacking height 30 cm, adm. load capacity 3 kN/m² (300 kg/m²).

Compensation platform LAB 130/240

Compensation platform LAB 130/240Zoom
galvanized, to accomplish length adjustments up to 2,00 m. It is attached to the adjacent platforms with two (2) integrated reversible couplings and is secured against uplift and displacement. Adm. load capacity 2 kN (200 kg/m²).

Corner platform LAB 130

Corner platform LAB 130Zoom
galvanized, crescent-shaped platform without guard-railing for outside corners between 70° and 180°. The guard-railings have to be ordered separately and need to be attached to the corner platform before use. The corner platform is secured against uplift and shifting by attaching the integrated couplers to the adjacent platforms. Adm. load capacity = 3 kN/m² (300 kg/m²).

Railing for corner platform LAB

Railing for corner platform LABZoom
galvanized, for each corner platform three (3) guard-railings are required, which are self-securing when assembled. The railings are connected to each other with integrated couplings. When using a pin connector LAB this railing can also be used as railing extension.

Uni-platform LAB 130/140

Uni-platform LAB 130/140Zoom
galvanized, versatile supplement to the working scaffold LAB 130. Can be applied as inner corner, as working platform with a length of 1,40 m (+ railing 140) or as compensation platform up to 1,00 m. Four (4) connectors for single scaffolding brackets are integrated (incl. 4 pins 16/120).

Railing 140 LAB

Railing 140 LABZoom
galvanized, pluggable railing for Uni-platform LAB 130/140 when used as a working scaffold with a length of 1,40 m or as compensation platform. It also serves as railing extension.

Single scaffolding bracket LAB

Single scaffolding bracket LABZoom
galvanized, it can be used as single bracket beneath corner platforms when applied in acute-angled corners, beneath compensation platforms or Uni-platforms. When used as single bracket, a guard-railing post 48/100 is additionally required.

Guard-railing post 48/100 LAB

Guard-railing post 48/100 LABZoom
galvanized, to be used with single LAB-brackets. It is suited as railing extension for all kind of guard-railings.

Extension for guard-railing LAB

Extension for guard-railing LABZoom
galvanized, with protective steel mesh (width 100x100 mm), to extend the railing by 1,00 m.

Side railing LAB

Side railing LABZoom
galvanized, with integrated protective steel mesh (width 100x100 mm). Side protection for the working scaffold LAB, it is provided with an integrated coupling, a limit stop and a clamping device.

Board holder 48 LAB

Board holder 48 LABZoom
galvanized, the board holder LAB permits the attachment of railing boards at each position of the railings and brackets.

Coupling pin 48 LAB

Coupling pin 48 LABZoom
galvanized, to attach a scaffold tube to a railing post (e.g. when protection nets are used). It is attached to the railing post 48/100 LAB with a pin 14/90.

Pin connector LAB

Pin connector LABZoom
galvanized, to connect corner railings LAB to each other for height extension. The railings of each level have to be connected to each other.

Bracket extension LAB

Bracket extension LABZoom
galvanized, on the one hand the bracket extension allows bridging wall openings, and on the other hand it facilitates to position the platforms about 1,30 m higher. It is provided with a pin 16/20 and a spacer. If wall openings of > 2,50 m have to be bridged, pressure rods LAB are additionally required.

Pressure rod LAB

Pressure rod LABZoom
galvanized, it is used together with the bracket extension when wall openings > 2,50 m have to be bridged. Delivery includes two (2) pins 16/20.

Height adjustment 60/100 LAB

Height adjustment 60/100 LABZoom
galvanized, permits lowering of LAB 130 platforms beneath eaves by 60 cm or 100c m (two possible positions). The height adjustment is secured to the platform with a pin 16/80 (delivery included) before flying the platforms.

Combi ledger LAB

Combi ledger LABZoom
galvanized, nailing ledger for single scaffolding bracket LAB to mount job-built planking or to adjust height if the compensation platform is provided with a bracket only at one side (e.g. in inside corners).

Bracket connection LAB

Bracket connection LABZoom
galvanized, permits to fasten a single scaffolding bracket LAB to the corner platform LAB in acute-angled corners. The single scaffolding bracket acts like a pressure rod. Delivery includes two (2) pins 16/80, a corner support LAB is additionally required.

Corner support LAB

Corner support LABZoom
galvanized, with the corner support LAB the single scaffolding bracket is made up to a corner bracket. Delivery includes two (2) pins 12/80 with cotter pin.

Scaffold tube 110 LAB

Scaffold tube 110 LABZoom
galvanized, supplement for Uni-platform LAB 130/140 in combination with single scaffolding bracket LAB. It serves to brace the single brackets when the Uni-platform is lifted.

Transport spreader LAB

Transport spreader LABZoom
galvanized, foldable, max. load capacity 10 kN (1 t). To move LAB-working scaffolds beneath the eaves. Please observe Instruction Manual.

Pins

PinsZoom
galvanized, Ø 16 mm, self-locking through tilting end. To secure various accessories (pin is integrated) of the working scaffold LAB.

Suspension shoe LAB

Suspension shoe LABZoom
galvanized, together with a sleeve LAB and a screw LAB it provides a safe suspension point.

Sleeve LAB

Sleeve LABZoom
built-in sleeve with Dywidag thread Ø 26,5 mm (length 27 cm), to enable the installation of the suspension shoe LAB. A screw LAB is additionally required.

Screw LAB

Screw LABZoom
galvanized, with Dywidag-thread Ø 26,5 mm. It serves to screw the suspension shoe LAB into the sleeve. Length of thread 25 cm.

Suspension loop 10

Suspension loop 10Zoom
uncoated, to suspend a platform, loop diameter 10 mm.

Tube suspension shoe LAB

Tube suspension shoe LABZoom
galvanized, together with sleeve LAB and screw LAB it provides a safe suspension point for the suspension tube 150 LAB.

Suspension tube 150 LAB

Suspension tube 150 LABZoom
galvanized, it is hooked into two (2) tube suspension shoes LAB and permits the suspension of the working scaffold LAB at the joint of two scaffolds. With the tube length of 1,50 m no exact fitting of the anchoring points is needed.

Loop plate LAB

Loop plate LABZoom
galvanized, is secured to concrete slab with at least two (2) dowels (Fischer FZA 14x60 M8I or similar) and serves to suspend working scaffolds LAB 130.

Suspension plate LAB

Suspension plate LABZoom
galvanized, it is secured to the concrete slab with at least two (2) dowels (Fischer FZA 14x60 M8I or similar) and serves to suspend the working scaffolds LAB 130.

LAB-suspension for prefabricated parts

LAB-suspension for prefabricated partsZoom
galvanized, to suspend the working scaffold LAB to prefabricated walls. Adm. loading 2 kN/m² (200 kg/m²) when used with LAB 130/340.

Sleeve for LAB-suspension for prefabricated parts

Sleeve for LAB-suspension for prefabricated partsZoom
cast-in plastic part (lost), is required for each application of the LAB-suspension device for prefabricated concrete parts.
 
 
Termeni Tipărire
 © MEVA Schalungs-Systeme GmbH