Sisteme de cofraje
 

STB

 

Cadrul de susţinere

Domenii de utilizare Caracteristici / Avantaje Lista de produse
 

Înalt & puternic

Înălţimi peste 12 m
Diafragma cofrată pe o singură latură prezintă cerinţe tehnice speciale pentru sistemul utilizat. Cadrul MEVA STB s-a impus în cadrul a nenumărate utilizări dificile, atingând limitele imposibilului – şi în cazul utilizării pentru diafragmele extrem de înalte. Spre deosebire de diafragmele cofrate pe două laturi, în cazul celor cofrate pe o singură latură întreaga presiune a betonului trebuie direcţionată din cofrare în construcţie, respectiv în fundaţie. Cadrele MEVA rezolvă problema sigur şi eficient prin intermediul unui sistem de ancorare încorporat în fundaţie, radier sau planşeu.
Cadrul de susţinere STB face posibilă cofrarea pe o singură latură pentru înălţimile diafragmelor de peste 12,00 m, pentru:

  • pereţi mulaţi
  • sprijiniri de maluri
  • ziduri de sprijin
  • tuneluri

Sistemul este caracterizat prin înălţimi de diafragmă de peste 12,00 m la un necesar redus de spaţiu de 2,45 m al STB 450. Cadrul poate fi utilizat şi ca susţinere pentru soluţiile speciale de cofrare.

Soluţie de execuţie

 CARACTERISTICI

AVANTAJE

  • STB 300 (înălţime constructivă 3,00 m) pentru diafragme de până la 3,50 m
  1. soluţie eficientă la dimensiuni compacte, pentru înălţimile obişnuite de diafragmă, cu utilizare la construcţiile de parcări subterane şi în construcţiile de locuinţe
  • STB 450 (înălţime 4,50m la o adâncime de numai 2,45m) pentru pereţi până la 5,00 m, cu posibilitate de supraînălţare
  1. element de bază compact şi transport rentabil (nu necesită transport agabaritic)
  • sistem modular: cu supraînălţare, cu elemente de supraînălţare cu înălţime de 1,50m, până la înălţimi ale pereţilor de 12,00m, cu sprijinire adiţională prin popi de sprijin spaţiali Triplex SB.
  1. înălţime de fixare minimă şi înălţime maximă din cadrul tuturor sistemelor de pe piaţă, ideal şi pentru şantierele cu spaţiu de lucru îngust
  • consolă de susţinere SK 150 pentru utilizarea pe înălţimi de până la 2,00m înălţime, înclinarea este ajustabilă
  1. decofrare flexibilă şi eficientă a radierului – şi cu benzi de rost

Construcţie

 CARACTERISTICI

AVANTAJE
  • construcţie din oţel, solidă, extrem de rezistentă la sarcină, unităţi de supraînălţare de dimensiuni mici
  1. siguranţă statică sporită, adaptare optimă inclusiv la situaţii dificile pe şantier, logistică simplă
  • ancorare cu filet DYWIDAG în radier,  resp. fundaţie
  1. sistem de ancorare la standardele actuale ale pieţei; preluarea de sarcină în funcţie de diametru şi distanţa de ancorare permite ajustarea optimă la situaţia de pe şantier
  • poate fi combinat atât cu sistemele de cofraje de diafragmă MEVA, cât şi cu cofraje speciale, ca de exemplu cu placa cofrantă din material sintetic alkus ca foaie cofrantă
  1. soluţii practice pentru geometrii deosebite, cofraje de dimensiuni mari cu suprafeţe de beton extrem de omogene
Deschide detalii
Închide toate detaliile
 

Support frame STB 300

Support frame STB 300Zoom
sturdy steel construction, coated, height 3,00 m. To brace single-sided wall formwork up to a pouring height of max. 3,50 m. A spindle allows to set the formwork plumb.

Base extension STB 300/200

Base extension STB 300/200Zoom
coated, it supplements the support frame STB 300 for special applications, which require a detailed planning and static calculation by MEVA engineers.

Cross beam 300

Cross beam 300Zoom
coated, to link formwork and support frames by means of flange screws. It allows to build transport units. Weld-in nuts guarantee a spacing of support frames which is adpated to all MEVA wall formwork systems.

M-alignment rail 44

M-alignment rail 44Zoom
galvanized, in connection with support frames STB 300 it is used as tie-beam to transmit the forces from the support frame into the anchoring loops.

Flange screw

Flange screwZoom
galvanized, with Dywidag thread Ø 15 mm. To attach accessories to the multi-function profiles, e.g. alignment rails, cross braces, cross beams 300, formwork-prop connectors, etc.

Support frame STB 450

Support frame STB 450Zoom
sturdy steel construction, coated, height 4,50 m. To brace single-sided wall formwork up to a pouring height of max. 5,00 m. A spindle allows to set the formwork plumb.

Height extension 150

Height extension 150Zoom
coated, height 1,50 m. Serves to extend the support frame STB 450 by 1,50 m, even several times. For heights exceeding 6,00 m, Triplex braces SB and base extensions are additionally required, necessary connecting devices (bolts M20x50 and locking nuts M20 as well as bolts M30x150 and locking nuts M30) are included in the delivery.

Base extension

Base extensionZoom
coated, serves to extend support frames STB 450 backwards (even several times) and to attach Triplex braces SB.

Twin channel

Twin channelZoom
coated, to be used with support frame STB 450. It transfers the loads from the support frame into the anchor bars.

Fixing screw 35/DW15

Fixing screw 35/DW15Zoom
galvanized, to attach a support frame to the tie holes of panels in horizontal position, a flange nut 100 or an articulated flange nut 15/120 are required.

Stop end bracket SB 110

Stop end bracket SB 110Zoom
coated, to form stop ends when the pouring height exceeds 4m, max. wall thickness 1,10 m. A clamping device for stop end brackets SB 110 or, as an alternative, tie rods DW 15 (l=45 cm) are required to fixate the stop end bracket SB 110 to the support frame.

Clamping device for stop end -bracket SB 110

Clamping device for stop end -bracket SB 110Zoom
coated, to connect the stop end bracket to the support frame. A flange nut 100 or an articulated flange nut 15/120 are additionally required.

Cross brace STB

Cross brace STBZoom
coated, to support the inside corner area of a single-sided wall formwork. Dimension 137x137 cm, weld-in DW-threaded nuts for attachment of two STB 300 or STB 450. Additional flange screws are required to fixate the cross brace to the formwork and the support frame to the cross brace.

Trolley waler

Trolley walerZoom
coated, to enable a fast transport of support frames in restricted areas if it is not possible to use a crane. The trolley waler is attached to the support frame units. Wheel adapters, trolley spindles and castors are additionally required. Please observe Instruction Manual.

Wheel adapter for trolley waler

Wheel adapter for trolley walerZoom
galvanized, to install swivel-type castors, suitable for castor 2 tons or castor 6 tons.

Trolley spindle 48/70

Trolley spindle 48/70Zoom
galvanized, to raise support frame units in order to attach castors.

Swivel-type castor 2 t

Swivel-type castor 2 tZoom
suited for wheel adapter for trolley waler. Load capacity 2 t with slide bearing, total height 305 mm, plate size 175x140 mm, screw hole spacing 140x105 mm, drill hole size d=14 mm, cantilever 75 mm.

Swivel-type castor 6 t (10 t)

Swivel-type castor 6 t (10 t)Zoom
Load capacity 6 t with ball bearing, total height 330 mm, plate size 225x200 mm, screw hole spacing 210x200 mm, drill hole size d=18 mm, cantilever 85 mm. Load capacity 10 t with ball bearing, total height 430 mm, plate size 400x300 mm, screw hole spacing 340x240 mm, drill hole size d=26 mm, cantilever 110 mm.

Brace bracket SK 150

Brace bracket SK 150Zoom
coated, to form stop ends for base plates with a thickness of up to 1,50 m. Braces SRL 120 or SRL 170 have to be ordered separately.

Positioning support SK

Positioning support SKZoom
coated, permits the exact levelling and positioning of the stop end when used with the brace bracket 150 - even on sloped surfaces.

Brace SRL

Brace SRLZoom
galvanized, it consists of a right-hand and a left-hand spindle as well as a revolving centre part. It is delivered without foot plate and formwork-prop connector.

Triplex SB

Triplex SBZoom
galvanized, together with the base extension it provides additional support when the concreting height exceeds 6,00 m. Refer to chapter \"Triplex\" for further details.

Tie rod DW

Tie rod DWZoom
uncoated, not weldable, with Dywidag-thread. To transfer the loads from the support frame into the floor slab or foundation. Ø 15 mm: adm. load capacity 90 kN Ø 20 mm: adm. load capacity 160 kN Ø 26.5 mm: adm. load capacity 250 kN

Anchor loop

Anchor loopZoom
uncoated, not weldable, with Dywidag-thread. To transfer the loads from the support frame into the floor slab or foundation. Ø 15 mm: adm. load capacity 2 x 90 kN = 180 kN Ø 20 mm: adm. load capacity 2 x 160 kN = 320 kN.

Articulated flange nut

Articulated flange nutZoom
forged, galvanized, with Dywidag thread Ø 15mm (Ø 20 mm), diameter of plate 120 mm (140 mm), maximum inclination 10°, spanner width 27 mm (36 mm) , max. load capacity 90 kN (160 kN). Reduces wear of panel coating.

Flange nut 100

Flange nut 100Zoom
forged, cut thread, for Dywidag tie rods with diameter 15 mm, diameter of plate 100 mm, SW 27, admissible load capacity 90 kN (DIN 18216).

Coupling nut

Coupling nutZoom
with Dywidag-thread, to connect tie rods to the anchor loop when length extension is necessary. Ø 15 mm: adm. load capacity 90 kN, SW 30 Ø 20 mm: adm. load capacity 160 kN, SW 36 Ø 26,5 mm: adm. load capacity 250 kN, SW 46.

Anchoring auxiliary

Anchoring auxiliaryZoom
facilitates the placing of tie rods at 45° into the supporting structure when support frames are used.

Hexagonal nut

Hexagonal nutZoom
galvanized, with Dywidag-thread. To tie the anchors in the bottom slab and at the support frame, is used with a counter plate to increase the pull-out-resistance. Ø 15 mm: adm. load capacity 90 kN, SW 30 Ø 20 mm: adm. load capacity 160 kN, SW 36 Ø 26,5 mm: adm. load capacity 250 kN, SW 46.

Counter plate

Counter plateZoom
galvanized, is used with tie rods DW 15, 20 or 26,5 and the appropriate hexagonal nuts to anchor the support frame. Hole diameter 25 mm or 38 mm.

Scaffold tubes

Scaffold tubesZoom
galvanized, to reinforce large-size units of support frames or climbing scaffolds for crane ganging.

Rigid coupler 48/48

Rigid coupler 48/48Zoom
galvanized, to connect two (2) scaffold tubes with Ø 48,3 mm at an angle of 90° (spanner width 22 mm).

Swivel-joint coupler 48/48

Swivel-joint coupler 48/48Zoom
galvanized, to connect two (2) scaffold tubes with Ø 48,3 mm at any angle required.

Bolt-on coupler 48/M14

Bolt-on coupler 48/M14Zoom
galvanized, permits the attachment of scaffold tubes Ø 48,3 mm to support frames, climbing brackets etc.

Joint coupler 48/48 (SW 22)

Joint coupler 48/48 (SW 22)Zoom
galvanized, to attach scaffold tubes of Ø 48,3 mm at tube joints, it is used together with a tube connector 48.

Tube connector 48

Tube connector 48Zoom
galvanized, supplement to rigid coupler 48/48. It is used to reinforce the joint of two tubes.
 
 
Termeni Tipărire
 © MEVA Schalungs-Systeme GmbH