Sisteme de cofraje
 

Mammut 350

 

Cofrajul pentru diafragme

Domenii de utilizare Caracteristici / Avantaje Lista de produse
 

Mai înalt, mai rapid, mai eficient

Mammut 350 reprezintă noua dimensiune a cofrajelor de diafragmă, având o înălţime standard de 3,50 m şi simetrie absolută la ancorare şi rostuire. Elementul de bază are două înălţimi: 350 şi 250 cm şi se poate asambla pe orizontală sau verticală. Astfel, acoperă o suprafaţă de cofrare de 8,75 m².

Sistemul poate fi utilizat în:

  • construcţiile industriale şi civile
  • construcţiile speciale
  • construcţiile de locuinţe

Toate accesoriile Mammut 350 şi Mammut sunt compatibile.

Rezistenţa admisibilă la presiune a betonului proaspăt: 100 kN/m².

Orice viteză de betonare, până la o înălţime de 4m!

Panouri

CARACTERISTICI

AVANTAJE

  • Panou cu dimensiuni standard de 350 x 250 cm pentru o suprafaţă de cofrare de 8,75 m²
  1. avantaje economice, în special la proiectele la care variază înălţimea de nivel, ca de exemplu la locuinţe / clădiri de birouri cu parcare subterană
  • prin asamblare pe orizontală sau verticală se obţine o simetrie absolută la ancorare şi rostuire
  1. minimizarea zonelor de completare
  2. adaptare rapidă la geometria partiurilor
  • colţuri interioare şi exterioare de 90° şi 135° şi colţ articulat cu dispozitiv de blocare pentru unghiuri frecvente între 60° şi 180°
  1. toate configuraţiile de colţ pot fi realizate cu panouri standard
  2. înaintare mai rapidă a lucrărilor de construcţie
 

Presiunea betonului

 CARACTERISTICI

AVANTAJE

  • rezistenţa admisibilă la presiune a betonului proaspăt (DIN 18218) pe toată suprafaţa 100 kN/m²
  1. orice viteză de betonare până la o înălţime de 4 m
  2. viteză mare de betonare şi la diafragme foarte înalte
 

Rama

 CARACTERISTICI

AVANTAJE

  • ramă din profile închise, foarte durabile, din oţel
  1. rigiditate sporită la torsiune, durată de viaţă sporită
  • Profilele de ramă MEVA sunt prevăzute cu două straturi. Baza o constituie o grunduire neagră anticorozivă. O protecţie suplimentară împotriva coroziunii este asigurată prin conservarea spaţiului gol al ramei cu ceară. Stratul roşu dintr-un praf sintetic special este aplicat printr-o procedură de vopsire în câmp electrostatic, crescând astfel rezistenţa la zgârieturi şi lovituri a ramei.
  1. protecţie sporită anticorozivă
  2. necesitate redusă de curăţare, datorită aderenţei scăzute a betonului
  3. durată de viaţă sporită
  • locaş de poziţionare la panouri mari cu lăţimi de 250 şi 125 cm
  1. pentru poziţionarea şi ajustarea simplă cu levier
 

Profilul multifuncţional

CARACTERISTICI

AVANTAJE
  • profil multifuncţional MEVA ce corespunde cerinţelor practice, cu piuliţe fixate prin sudură (filet DYWIDAG)
  • profile multifuncţionale adiţionale în punctul de ancoraj
  1. prindere simplă a accesoriilor, ca de exemplu a popilor şi a riglelor de aliniere, a consolelor de lucru, etc.
 

Găuri de ancoraj, îmbinări ale panourilor

CARACTERISTICI

AVANTAJE

  • gaură de ancoraj cu bucşă conică din oţel, sudată pe ambele părţi
  1. utilizare simplă a tiranţilor DW 15 şi DW 20
  2. durată lungă de viaţă; este posibilă ancorarea şi la cofrajele înclinate
  • poziţia găurii de ancoraj: 3 x la elemente cu înălţimea de 350, 2 x la elemente cu înălţimea de 250 şi 1 x la elemente cu înălţimea de 125 cm
  • dispunere absolut simetrică a tuturor locurilor de ancoraj
  1. ancorare şi rosturi dispuse egal atât la supraînălţarea pe verticală, cât şi la îmbinarea pe orizontală
  • îmbinarea panourilor cu cleştele conceput de firma MEVA: o singură piesă, numai 3 kg
  1. economie de timp la montaj: sunt de ajuns câteva lovituri de ciocan pentru a obţine o îmbinare continuă, strânsă şi alinierea fără decalaje a panourilor
  2. fără accesorii individuale ce pot fi pierdute, putând fi montat cu o mână şi de pe scară
 
Deschide detalii
Închide toate detaliile
 

M 350-panels

M 350-panelsZoom
Construction height 12 cm, frame profile width 60 m, three tie holes per panel height 350 cm, two tie holes per panel height 250 cm. The frames of M 350-panels are made of closed steel profiles and are torsion-proof, corrosion-resistant and easy to clean thanks to a state-of-the-art surface coating. M 350-panels are standardly fitted with alkus AL 20 all-plastic forming face. All-around grooves and M-assembly locks guarantee a tight and perfectly aligned panel connection. Conical anchor sleeves are weld into the frames. Multi-function profiles allow for an easy, fast and safe attachment of accessories.

M 350-stripping panel

M 350-stripping panelZoom
steel construction with steel sheeting, state-of-the-art surface coating, two-part panel with tie holes. Panel is locked with flange screws 100 (number depends on panel height) screwed into assembly thread, it is disengaged by inserting the flange screw into stripping thread.

M 350-alumunium filler

M 350-alumunium fillerZoom
Aluminium, plastic-coated, with tie holes. For length adjustments of 5 cm, particularly in corners, for each filler 2 or 3 Uni-assembly locks are required.

M 350-timber profile

M 350-timber profileZoom
Timber profile with groove. To support job-built fillers of 17 cm or more, or to connect job-built formwork with a 21 mm facing, is attached to standard M 350-panels with 2 or 3 M-assembly locks. Delivery and weight by pairs.

M 350-inside corner 350/25

M 350-inside corner 350/25Zoom
for 90°-corners, side length 25 cm. Steel frame with tie holes. Frame with state-of-the-art surface coating.

M 350-outside corner 350

M 350-outside corner 350Zoom
steel construction, galvanized, together with M 350-panels and M-assembly locks it provides a tight outside corner assembly for 90° angles.

M 350-inside corner 135°, 350/15

M 350-inside corner 135°, 350/15Zoom
steel construction with steel sheeting, state-of-the-art surface coating, for 135° corner configurations. Side length 15 cm, with tie holes.

M 350-outside corner 135°, 350/25

M 350-outside corner 135°, 350/25Zoom
steel construction with steel sheeting, state-of-the-art surface coating. Outside corner with tie holes suited for 135° corner configurations, side length 25 cm.

M 350-hinged inside corner 350/40

M 350-hinged inside corner 350/40Zoom
steel construction with steel sheeting, state-of-the-art surface coating. Side length 40 cm, adjustable angle 60°-180°.

M 350-hinged outside corner 350/12.5

M 350-hinged outside corner 350/12.5Zoom
steel construction with steel sheeting, state-of-the-art surface coating. Side length 12,5 cm, adjustable angle 60°-180°.

M 350-stripping corner

M 350-stripping cornerZoom
Steel construction with steel sheeting, state-of-the-art surface coating, side length 25 cm, with tie holes. When the bell-crank lever is pushed upwards with a crowbar, the corner is removed 17,5 mm away from the concrete and the formwork 35 mm away from the concrete on both sides.

M-assembly lock

M-assembly lockZoom
galvanized, to tightly connect and align Mammut- and Mammut 350-panels. Clamping length 12 cm. For panel height up to 300cm two (2) M-assembly locks are required per panel joint, for panel height 350 cm three (3) locks are required.

Uni-assembly lock

Uni-assembly lockZoom
galvanized, for stepless compensations, clamping length 22 cm or 28 cm.

Combi-lock with coupling

Combi-lock with couplingZoom
galvanized, to attach push-pull props at the panel joints of the wall formwork systems AluStar, StarTec, Mammut and Mammut 350. Clamping length 8, 10 and 12 cm.

Flange screw

Flange screwZoom
galvanized, with Dywidag thread Ø 15 mm. To attach accessories (e.g. alignment rails, brace frames, push-pull props, etc.). Length of thread 18 cm (28 cm).

M-alignment rail 44

M-alignment rail 44Zoom
galvanized, short alignment rail to brace panel joints for crane ganging and to reinforce filler areas.

M-alignment rails

M-alignment railsZoom
galvanized, to brace panel joints for crane ganging, to bridge problem areas, to brace compensation areas and to build stop ends (with stop end fixtures). Is attached to the formwork with flange screws.

M-outside corner bracket

M-outside corner bracketZoom
galvanized, together with M-panels and flange screws 18 it provides a tight outside corner assembly for 90° angles, drilled hole for corner platform brackets.

M-column bracket

M-column bracketZoom
galvanized, to build rectangular columns with M-panels or stop ends, etc. It is attached to the multi-function profile with flange screws 18.

Corner bracket 40/60

Corner bracket 40/60Zoom
galvanized, side lengths 40 cm and 60 cm, for inside and outside corners and column formwork.

Stop end bracket 40/60

Stop end bracket 40/60Zoom
galvanized, to form stop ends, is suited for frame formwork panels with a profile width of 40 mm or 60 mm, max. wall thickness 40 cm. Stop end bracket 75 cm - 60/23 is suited for a max. wall thickness of 75 cm (2.5 Inch), for profile widths of 23 mm and 60 mm.

Column clamp

Column clampZoom
galvanized, to attach alignment rails to M-panels when stop ends are formed. It is suited for the frame profiles of Mammut/Mammut 350 (60 mm). A flange nut 100 or an articulated flange nut 15/120 are required in addition. It is attached to the multi-function profile with a flange screw 18.

Plug D26

Plug D26Zoom
grey, to close unused tie holes of Mammut and Mammut 350.

Articulated flange nut

Articulated flange nutZoom
forged, galvanized, with Dywidag thread Ø 15 mm (Ø 20 mm), diameter of plate 120mm (140 mm), maximum inclination 10°, spanner width 27 mm (36 mm) , max. load capacity 90 kN (160 kN). Reduces wear of panel coating.

Flange nut 100

Flange nut 100Zoom
forged, cut thread, for Dywidag tie rods with diameter 15 mm, diameter of plate 100 mm, SW 27, admissible load capacity 90 kN (DIN 18216).

Drive nut 60

Drive nut 60Zoom
galvanized, Dywidag thread Ø 15 mm, diameter of plate 60 mm, adm. load capacity 90 kN. It is used to anchor the formwork to the ground or a wall connection.

Tie rod DW

Tie rod DWZoom
uncoated, not weldable. Dywidag thread, adm. load capacity 90 kN (Ø 15 mm) or 160 kN (Ø 20 mm), to tie panels of a double-­sided formwork.

Uni-tie claw

Uni-tie clawZoom
galvanized, permits tieing directly above or beside panels. It is suited for panels with a frame profile width of 40 mm (AluStar/StarTec) and 60 mm (Mammut/Mammut 350).

Spanner

SpannerZoom
inset yellow chromated, spanner width 27 mm. To tighten and loosen flange nuts 100, articulated flange nuts 15/120 and flange screws (spanner width 36 mm for articulated flange nuts 20/140).

Hexagonal nut

Hexagonal nutZoom
galvanized, with Dywidag-thread. To tie the anchors in the bottom slab and at the support frame, is used with a counter plate to increase the pull-out-resistance. Ø 20 mm: adm. load capacity 160 kN, SW 36

Coupling nut

Coupling nutZoom
with Dywidag-thread, to connect tie rods to the anchor loop when length extension is necessary. Ø 20 mm: adm. load capacity 160 kN, SW 36.

Counter plate

Counter plateZoom
galvanized, is used with tie rods DW 15, 20 or 26., and the appropriate hexagonal nuts to anchor the support frame. Hole diameter 25 mm.

M-crane hook

M-crane hookZoom
to move panels. Self-locking, load capacity 15 kN (1,5 t). Always two (2) crane hooks required per gang. Please refer to Instruction Manual for application and safety test.

Crane slings

Crane slingsZoom
Four (4) polyester ropes, length 5 m, with 60 cm lifting chain and four (4) lifting hooks, max. load capacity 20 kN (2 t), to load and unload trucks and to move panel stacks near the ground.

Lifting hook

Lifting hookZoom
galvanized, with these lifting hooks any 4-roped crane slings available on site can be used to move the panel stacks (always use 4 hooks at a time). Please refer to Instruction Manual for application and safety test.

Crane slings Stapos

Crane slings Stapos
Crane slings for panels with a frame profile width of 40 mm or 60 mm. Four (4) crane slings are required to move and transport panel stacks. Max. stacking height 126 cm = 10 panels, max. load capacity per crane sling10 kN, max. weight of stack 2 tons (not shown).

Scaffolding bracket

Scaffolding bracketZoom
galvanized, yellow, pluggable. It is used as working and safety scaffold, is attached to the multi-function profile and secured to the multi-function profile below by means of a flange screw 18. The planking can be mounted to the brackets. Working width approx. 90 cm (125 cm). Guard-railing post 100 or 140 is required in addition. Bracket spacing depends on type of planking .

Guard-railing post

Guard-railing postZoom
galvanized, is attached to the scaffolding bracket.

Side railing

Side railingZoom
galvanized, for scaffolding brackets.

Brace frame 250

Brace frame 250Zoom
galvanized, to align and brace the formwork. Available with or ­without formwork-prop connector, it consists of a push-pull prop R 250 (190-320 cm), a brace SRL 120 (90-150 cm) and a double-jointed footplate, the formwork-prop connectors are attached to the formwork with flange screws 18.

Formwork-­prop connector

Formwork-­prop connectorZoom
galvanized, to connect braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile by means of a flange screw 18. Delivery includes head bolt 16/90 and cotter pin 4.

Foundation tape

Foundation tapeZoom
galvanized, hole spacing 50 mm, hole Ø 16 mm, length 50 m, adm. tractive force 10 kN, to be cut at hole center. Together with the appropriate tensioner it serves as bottom anchoring when panels are assembled in horizontal position.

Tensioner M for foundation tape

Tensioner M for foundation tapeZoom
galvanized, to connect the foundation tape to Mammut or Mammut 350-panels, it serves as bottom anchoring when panels are assembled in horizontal position. Two (2) tensioners are required per anchoring position.

Trolley for foundation tape

Trolley for foundation tape
galvanized, to transport and cut foundation tape to length, suitable for one roll, pneumatic wheels (not shown).

Folding access platform BKB 125

Folding access platform BKB 125Zoom
self-locking, ready-made platform with a foldable guard-railing and an overall width of 125 cm, it is supsended onto the frame profile of the panels. The 48 mm thick planking is protected at the front ends. Stacking height 17 cm, load capacity 2 kN/m². This platform is used with the formwork systems AluStar/StarTec and Mammut/Mammut 350.
 
 
Termeni Tipărire
 © MEVA Schalungs-Systeme GmbH